Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be achieved in just a few procedures.

• First ensuring your red dot sight is powered on.
• Locate the small reinitialize button on the side of the device.
• Use a paperclip to activate the reset switch for approximately 5 seconds.
• Let go the switch and your Holosun EPS Carry Red Dot sight will restart.
• The red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it back to standard configuration is a breeze. First, determine the tiny button on the side of your optic. Then, press and hold it for around five seconds until you see the indicator light change. Your Holosun EPS Carry is now returned to its factory settings, ready for consistent targeting.

Bring Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Press and hold the power button for approximately 5 seconds.
• A message will flash, indicating that the reset is in progress.
• Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further problems, don't hesitate to contactsupport team.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Initially, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, press the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all click here settings Reinitialized to their default values.

Reinitialize your Holosun EPS Carry via a Factory Default Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the fix. This will return your sight to its factory settings, clearing any personalized configurations you've made. To execute this reset, follow these straightforward steps:

• First, find the reset lever on your EPS Carry.
• Then, press a thin object, like a paperclip, to activate the reset switch.
• During keep the reset switch activated, activate your EPS Carry.
• The sight will blink a message indicating that the reset is complete.

After the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page